How to measure
- Attic floor or crawlspace ceiling: measure length × width of the space you're insulating.
- Walls: measure each wall's length × height and subtract windows and doors.
- Find your IECC climate zone on the ENERGY STAR or DOE climate zone map (zones 1–8 across the US).
- Check what's there now: if the attic already has 3–4 in, tick the box — the recommendation changes.
How the insulation calculation works
Batt bags = area × (1 + waste) ÷ sq ft per bag Blown bags = area ÷ maximum coverage per bag Blown depth ≥ the label's minimum thickness for that R-value
Every bag lists how many square feet it covers. Batts: pieces per bag × batt size (an R-30, 24 × 48 in bag of 11 pieces covers 88 sq ft). Loose fill: a chart of bags per 1,000 sq ft and minimum thickness for each R-value.
Blown-in only reaches its rated R-value when you install both the bag count and the minimum thickness from the chart. That's why this calculator never converts depth to R-value on its own.
Worked example
A 1,000 sq ft attic in climate zone 5, insulated with R-30 batts 24 in wide, with 5% waste; then the same attic blown to R-49.
- ENERGY STAR for zone 5, uninsulated attic: R-60 (R-49 when topping up 3–4 in)
- Batts: 1,000 × 1.05 = 1,050 sq ft ÷ 88 sq ft per bag = 11.9 → 12 bags
- Blown-in R-49 (AttiCat chart): 1,000 ÷ 39.9 sq ft per bag = 25.1 → 26 bags, at least 17 in deep
12 bags of R-30 batts — a single layer is below the R-60 recommendation, so plan a second layer — or 26 bags of blown-in for R-49.
How much extra to allow
Batts get trimmed around wiring, pipes, blocking and odd bays. Blown-in has no offcuts but must reach the full depth everywhere, including the edges.
| Situation | Allow |
|---|---|
| Open attic, regular joists | 0–5% |
| Walls with many outlets and pipes | 5–10% |
Reading your result
Bags to buy is the shopping list. For blown-in, mark the minimum depth on a few rulers stapled to the joists so you can see when you've reached it.
The R-value comparison tells you whether one layer is enough or a second layer is worth adding.
Assumptions
- Recommended R-values are ENERGY STAR's retrofit table for wood-framed homes, based on the 2021 IECC (Table R402.1.3).
- Batt coverage from the Johns Manville fact sheet; blown-in coverage from the Owens Corning AttiCat PINK data sheet. Other products differ — choose "Other" and use your label.
- Batt bag coverage is the batt area; framing takes up a little of a wall, so this slightly over-buys rather than under-buys.
- R-values are US units (ft²·°F·h/BTU); RSI = R × 0.1761.
Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.
When to call a professional
- Knob-and-tube wiring, vermiculite (which can contain asbestos), signs of moisture or mold, or recessed lights not rated for contact with insulation should be dealt with by a professional before insulating.
Frequently asked questions
How much insulation do I need in my attic?
ENERGY STAR recommends R-30 in zone 1, R-49 in zones 2–3 and R-60 in zones 4–8 for an uninsulated attic, and R-25 to R-49 when adding to 3–4 in of existing insulation.
How many square feet does a bag of insulation cover?
It's on the label. A Johns Manville R-13 bag of 15 × 93 in batts covers 106.56 sq ft; an R-30 bag of 24 × 48 in batts covers 88 sq ft. Owens Corning AttiCat blown-in covers 68.5 sq ft per bag at R-30 and 39.9 sq ft at R-49.
How deep is R-49 blown-in insulation?
It depends on the product. Owens Corning AttiCat PINK needs at least 17 in for R-49, along with the chart's bag count. Cellulose reaches the same R-value at a different depth.
Can I put new insulation over old?
Usually, yes — if the old insulation is dry and not compressed. Lay unfaced batts across the joists or blow loose fill on top. Don't add a second vapor retarder (faced batts) on top of existing insulation.