Skip to content
MeasureToBuy

Drywall Calculator

Enter the room's size and choose a sheet size. The calculator counts drywall sheets for the walls and ceiling separately, then estimates joint compound, paper tape and screws for finishing.

Measurements

Floor to ceiling.

Sheet size

32 sq ft · easiest to carry

Waste allowance

Offcuts at openings, corners and the top course. 10% for simple rooms, 15% for many openings or angles.

Advanced optionscoverage, sizes, custom values

A standard 3 × 7 ft door is 21 sq ft.

A typical 3 × 5 ft window is 15 sq ft.

Your estimate

You need 19 sheets of 4 × 8 ft drywall.

13 for the walls and 6 for the ceiling, including 10% waste.

Wall area
416 sq ft
Doors & windows
-51 sq ft
Wall board
365 sq ft
Ceiling board
168 sq ft
Waste
10%
Sheet size32 sq ft
4 × 8 ft
Wall sheets
13 sheets
Ceiling sheets
6 sheets
Buy4 × 8 ft sheets
19 sheets

Finishing (approximate)

Joint compound≈ 0.137 lb per sq ft of board
73 lb
All-purpose compound, 4.5-gal bucketsone per ~450 sq ft
2 buckets
Paper tape≈ 370 ft per 1,000 sq ft
197 ft
Tape rolls (500 ft)
1 roll
Drywall screws≈ 1 per sq ft
533 screws
  • Walls and ceiling are counted separately so leftover pieces aren't assumed to fit across both — ceilings are usually hung with the longest sheets you can lift.
  • Finishing quantities are rules of thumb for a standard level-4 finish. Heavy skim coats use more compound.
Wall elevation · sheet layout
14 ft8 ft
Long wall shown. Dashed lines mark sheet joints with sheets standing vertically; openings are cut out of full sheets.

Next step

Prime the new board

Fresh drywall and joint compound need a full coat of primer before paint.

Calculate primer

How to measure

  1. Measure the room's length and width along the floor and the wall height from floor to ceiling.
  2. Count doors and windows. Large openings save board; small ones mostly come out of sheets you'd buy anyway.
  3. Decide on sheet size. 4 × 8 ft sheets are easiest to carry and hang alone; 4 × 12 ft sheets mean fewer seams to tape and sand.
  4. Hanging the ceiling too? Leave 'Include the ceiling' on — it's counted separately.

How the drywall calculation works

Wall board     = 2 × (length + width) × height − doors − windows
Ceiling board  = length × width
Sheets         = board × (1 + waste %) ÷ sheet area, rounded up (walls and ceiling separately)
Compound       ≈ board × 0.137 lb per sq ft  (one 4.5-gal bucket ≈ 450 sq ft)
Paper tape     ≈ 370 ft per 1,000 sq ft
Screws         ≈ 1 per sq ft

Sheets are counted from area plus a waste allowance for cut-outs, corners and the top course. Walls and ceiling are rounded separately because offcuts from one rarely fit the other.

Finishing quantities scale with the board area. A 4.5-gallon bucket of all-purpose premixed compound (about 61.7 lb) finishes roughly 450 sq ft with tape, two coats and touch-ups. Paper tape runs about 370 ft per 1,000 sq ft, and screws about one per square foot at standard spacing.

Worked example

A 14 × 12 ft room with 8 ft walls, one door and two windows, walls and ceiling, 4 × 8 ft sheets, 10% waste.

  1. Walls: 2 × (14 + 12) × 8 = 416 − 21 − 30 = 365 sq ft × 1.1 = 401.5 ÷ 32 = 12.5 → 13 sheets
  2. Ceiling: 14 × 12 = 168 × 1.1 = 184.8 ÷ 32 = 5.8 → 6 sheets
  3. Board area: 365 + 168 = 533 sq ft
  4. Compound: 533 × 0.137 = 73 lb → 2 buckets
  5. Tape: 533 × 0.37 = 197 ft (one 500 ft roll); screws: about 533

Buy 19 sheets of 4 × 8 drywall, 2 buckets of all-purpose compound, a 500 ft roll of tape and about 530 screws.

How much extra to allow

Drywall waste comes from cut-outs around openings, short pieces at the top or end of a wall, and broken corners. Fewer, longer sheets reduce seams but can increase offcuts in small rooms.

SituationAllow
Simple rectangular room10%
Several windows or a closet12%
Angles, soffits, vaulted ceilings15%

Reading your result

The highlighted sheet count is the order. Wall and ceiling counts are shown so you can buy longer sheets for the ceiling if you like.

Finishing items are approximate — buy the compound and tape listed, and pick up extra if you're skim-coating.

If your walls are taller than a sheet, plan a horizontal layout or longer sheets to keep butt joints out of the middle of the wall.

Assumptions

  • Standard 1/2 in board on walls; many builders use 1/2 in sag-resistant or 5/8 in board on ceilings.
  • Doors are 21 sq ft and windows 15 sq ft unless you change them.
  • Finishing rates are rules of thumb for a level-4 finish with all-purpose premixed compound. Lightweight compound covers more per bucket by volume.
  • Corner bead, adhesive and outside corners aren't counted — add them in the cost panel's sundries.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Ceilings are heavy and awkward overhead — rent a drywall lift or hire a crew.
  • Fire-rated walls (garage-to-house, furnace rooms) need Type X board and specific screw spacing; follow your local code.
  • Moisture-prone areas such as showers need cement board, not drywall.

Frequently asked questions

How many sheets of drywall do I need for a 12 × 12 room?

With 8 ft walls, one door and one window, the walls are about 348 sq ft — 12 sheets of 4 × 8 with 10% waste. The 144 sq ft ceiling adds 5 more, for 17 sheets.

How much joint compound do I need?

About 0.137 lb per square foot of board, or one 4.5-gallon bucket of all-purpose premixed compound per 450 sq ft or so. A typical 12 × 12 room with ceiling needs about two buckets.

How many drywall screws per sheet?

About 32 for a 4 × 8 sheet — roughly one per square foot, at 16 in spacing on walls and 12 in on ceilings.

Should I use 4 × 8 or 4 × 12 sheets?

4 × 12 sheets mean fewer joints to tape and sand and fit a 12 ft wall in one piece. 4 × 8 sheets are lighter, fit in most vehicles and are easier to hang alone.

More lumber & carpentry calculators

All lumber & carpentry