Skip to content
MeasureToBuy

Generator Size Calculator

List the appliances you want to run at the same time with their running and starting watts. You'll get the total running load, the starting surge to plan for, and a recommended generator size with headroom.

Connecting a generator to house wiring requires a transfer switch or interlock installed by a licensed electrician. Never back-feed through an outlet.

Measurements

W

On the nameplate or manual. Amps × volts if only amps are listed.

W

Surge when a motor starts. Same as running watts for lights and electronics.

Your estimate

Look for a generator rated about 2.7 kilowatts or more.

700 W running plus a 1,500 W starting surge, with 20% headroom.

Running watts (all on together)
700 W
Largest starting surgeRefrigerator, one motor starting at a time
1,500 W
Starting watts neededrunning + largest surge
2,200 W
Recommended rated outputstarting watts × 1.2
2,700 W
  • Check both numbers on the generator: its running (rated) watts should cover your running total with room to spare, and its starting (peak) watts should cover the starting total.
  • The 20% headroom keeps the generator off full load, which is easier on it and on fuel. Starting two large motors at the same moment needs more — stagger them.
  • Fuel use depends on the model and the load. Check the spec sheet's run time at 50% load and plan fuel for the outage length you expect.
  • Connecting to house wiring needs a transfer switch or interlock installed by an electrician. Never backfeed through an outlet, and run the generator outdoors, well away from doors and windows.

Next step

Compare with grid running cost

See what the same appliances cost per day on your normal electricity rate.

Appliance running cost calculator

Also useful

Thinking about solar plus battery?

Start with how much electricity you use in a year.

Solar panel calculator

How to measure

  1. Decide what has to run together during an outage — usually the fridge, freezer, sump pump, some lights, a furnace fan, phones and the internet router.
  2. Find each appliance's running watts on its nameplate or in the manual. If it lists only amps, multiply by the voltage: 6 A × 120 V = 720 W.
  3. Find starting (surge) watts for anything with a motor or compressor — fridges, pumps, well pumps, AC units, power tools. If it's not listed, 2–3 times running watts is a common rough figure. Lights and electronics have no surge: enter the same number twice.
  4. Enter several identical items once with a quantity, like four lamps.

How the generator size calculation works

Running   = Σ running watts × quantity
Surge     = the largest (starting − running) of any one appliance
Starting  = running + surge
Recommend = starting × 1.2, rounded up to the next 100 W

Running watts add up: everything on at once draws the sum. Starting surge does not add up the same way, because motors only surge for a second or two. Assuming one motor starts at a time, the generator only has to absorb the single biggest surge on top of everything already running.

The 20% headroom keeps the generator from running at its limit, which is hard on the engine and makes voltage sag when something kicks on. It also leaves room for the item you forgot.

Worked example

Riding out an outage with a refrigerator (700 W running / 2,200 W starting), a ½ hp sump pump (1,050 / 2,150 W), 300 W of lights and two 100 W TVs.

  1. Running: 700 + 1,050 + 300 + (2 × 100) = 2,250 W
  2. Surges: fridge 2,200 − 700 = 1,500 W; sump pump 2,150 − 1,050 = 1,100 W
  3. Largest surge: 1,500 W (the fridge)
  4. Starting: 2,250 + 1,500 = 3,750 W
  5. With 20% headroom: 3,750 × 1.2 = 4,500 W

Look for a generator rated about 4.5 kW or more — for example one with 4,500+ running watts and a higher starting rating. A 3,500 W unit could start the fridge but would run close to its limit.

Reading your result

Generators list two numbers. Their running (rated) watts should cover your running total with room to spare. Their starting (peak or surge) watts should cover your starting total.

The recommended size includes headroom, so it's a target, not a hard minimum. Going much larger costs more and burns more fuel at light loads.

Fuel use depends on the generator and how heavily it's loaded. Use the spec sheet's run time at 50% load to plan how much fuel to store.

Assumptions

  • Only one motor starts at a time. If the fridge and sump pump can kick on together, add the second surge too, or stagger loads.
  • Wattages are typical nameplate figures you enter. Real starting watts vary by model and age.
  • Generator ratings are at sea level and mild temperatures; output drops at high altitude and in heat.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Connecting a generator to home wiring requires a transfer switch or an approved interlock, installed by a licensed electrician. Backfeeding through a dryer outlet or a 'suicide cord' can electrocute utility workers and start fires.
  • Standby (permanently installed) generators need a load calculation, permits and usually a gas line — get quotes from a licensed installer.
  • Run portable generators outdoors, at least 20 ft from doors and windows, and keep a carbon monoxide alarm in the house.

Frequently asked questions

What size generator do I need to run a refrigerator?

A typical fridge runs on about 700 W but needs around 2,200 W for a moment when the compressor starts. A generator rated around 2,700 W running covers it alone with headroom; add your other loads on top.

What's the difference between running watts and starting watts?

Running watts are what an appliance draws continuously. Starting (surge) watts are the brief spike — often two to three times higher — when a motor or compressor starts.

Can a generator power my whole house?

A large standby generator can, but most portable generators power a selection of essential circuits. Central AC, electric water heaters, ranges and dryers each draw several thousand watts.

How do I find an appliance's wattage?

Check the nameplate sticker, usually inside the door or on the back. If it shows amps, multiply by the voltage — 120 V for standard outlets, 240 V for large appliances.

More energy & hvac calculators

All energy & hvac