Skip to content
MeasureToBuy

Primer Calculator

Pick what you're priming — new drywall, bare wood, patches, or a dark color going light — and enter the room or the area. The calculator applies that surface's typical coverage and coats and tells you how many gallons to buy.

Measurements

Area from

Floor to ceiling.

Coats of primer

Set by the surface

Extra primer

Covers absorption, roller loss and touch-ups.

Advanced optionscoverage, sizes, custom values

A standard 3 × 7 ft door is 21 sq ft.

A typical 3 × 5 ft window is 15 sq ft.

Your estimate

You need about 2 gallons of primer.

365 sq ft at 1 coat and 300 sq ft/gal, plus 10% extra.

Wall area
416 sq ft
Doors & windows
-51 sq ft
Surface area
365 sq ft
Coats
1 coat
CoverageNew drywall
300 sq ft/gal
Extra
10%
Primer calculated
1.22 gal
With 10% extra
1.34 gal
Buy2 × 1-gal can
2 gal
  • New drywall needs a full coat of primer: bare paper and joint compound absorb paint at different rates and will flash through the finish.

Next step

Now the finish coats

Primer doesn't count as a coat of paint. Estimate the wall paint for the same room.

Calculate wall paint

How to measure

  1. For a room, measure length, width and wall height, and count doors and windows. Turn on the ceiling if it's new drywall too.
  2. If you already know the area (from the Wall Area Calculator or a drywall order), switch to Known area and enter it.
  3. Choose the surface honestly: fresh joint compound over most of a wall counts as new drywall, not patching.
  4. Check the coverage on your primer's label. If it differs from the typical figure, enter it under Advanced options.

How the primer calculation works

Surface area = walls − doors − windows (+ ceiling)
Area to prime = surface area × share primed   (100%, or 25% for spot priming)
Primer = area to prime × coats ÷ coverage
Buy    = primer × (1 + extra %), rounded up to cans

Primer is calculated like paint, but the coverage and number of coats depend on the surface. New drywall drinks a first coat (about 300 sq ft per gallon). Bare wood is thirstier still (about 200). Stain-blocking and dark-to-light jobs use a thicker film (about 250) and usually two coats.

Spot priming assumes patches cover about a quarter of the wall. If you've skim-coated or patched most of it, prime the whole wall — patches primed in isolation can 'flash' through the finish as dull spots.

Worked example

A newly drywalled 14 × 12 ft room with 8 ft walls, one door and two windows, priming walls and ceiling.

  1. Walls: 2 × (14 + 12) × 8 = 416 sq ft − 21 − 30 = 365 sq ft
  2. Ceiling: 14 × 12 = 168 sq ft; total 533 sq ft
  3. Primer: 533 × 1 coat ÷ 300 = 1.78 gallons
  4. With 10% extra: 1.78 × 1.1 = 1.95 gallons

Buy 2 gallons of drywall primer.

How much extra to allow

Primer goes on bare, porous surfaces, so the first few square feet soak up more than the label suggests. 10% extra is usually enough; use 15% on rough or very porous surfaces.

SituationAllow
Smooth new drywall, roller10%
Bare wood, masonry, textured walls15%

Reading your result

The highlighted number is the primer to buy. 'Area to prime' shows what the estimate is based on — check it matches what you plan to cover.

Primer doesn't replace finish coats. Plan the same number of paint coats you would on a primed wall.

Asking the store to tint primer toward your finish color can save a coat of paint on big color changes.

Assumptions

  • New drywall: about 300 sq ft per gallon, one coat (PVA or drywall primer-sealer).
  • Bare wood: about 200 sq ft per gallon, one coat. Knots and cedar need a stain-blocking primer.
  • Patched walls: about 25% of the area spot-primed, at 300 sq ft per gallon.
  • Dark-to-light or stain blocking: about 250 sq ft per gallon, two coats recommended. You can override the coats.
  • Doors are 21 sq ft and windows 15 sq ft unless you change them.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Smoke, fire and heavy water damage need specialist stain-and-odor-blocking primers and sometimes remediation first.
  • Homes built before 1978 may have lead paint. Test before sanding.

Frequently asked questions

How much primer do I need for new drywall?

About one gallon per 300 sq ft for one coat. A 12 × 12 room with 8 ft walls has about 350 sq ft of wall after openings, so with 10% extra plan on 2 gallons.

Do I need primer to paint over a dark color?

Usually yes. One or two coats of primer, ideally tinted gray or toward the new color, hides a dark color far more cheaply than three or four coats of finish paint.

Is paint-and-primer-in-one enough?

Over a sound, previously painted wall, often yes. On new drywall, bare wood, stains or big color changes, a dedicated primer seals and blocks better and costs less per gallon.

Do I need to prime patched spots?

Yes. Joint compound is far more porous than painted wall, so unprimed patches show through as dull spots. Spot-prime small patches; prime the whole wall if patches cover much of it.

More painting calculators

All painting