Skip to content
MeasureToBuy

Exterior Paint Calculator

Enter your house's perimeter, wall height and gable ends. The calculator subtracts doors and windows, adjusts for the siding texture, and rounds the paint to gallons and 5-gallon buckets.

Measurements

Add up the length of every outside wall you'll paint.

Ground or foundation line to the eaves. About 9–10 ft per story.

The triangles under the roof at each end. 0 for a hip roof.

Gable size from

Width of the wall under the gable.

Coats

Recommended

Extra paint

Covers absorption, roller loss and touch-ups.

Advanced optionscoverage, sizes, custom values
sq ft/gal

Printed on the can. Most exterior paints list 250–400 sq ft per gallon on smooth surfaces.

A standard 3 × 7 ft door is 21 sq ft. Count a garage door as 6–8 doors.

A typical 3 × 5 ft window is 15 sq ft.

Your estimate

You need about 10 gallons of exterior paint.

1,576 sq ft effective area at 2 coats and 350 sq ft/gal, plus 10% extra.

Walls (perimeter × height)
1,400 sq ft
Gable ends (2)7.5 ft high
225 sq ft
Doors & windows
-192 sq ft
Paintable area
1,433 sq ft
Siding factor · Lap / clapboard
1.1 ×
Effective area
1,576 sq ft
Coats
2 coats
Coverage
350 sq ft/gal
Extra
10%
Paint calculated
9.01 gal
With 10% extra
9.91 gal
Buy2 × 5-gal bucket
10 gal
  • Box the paint: mix the cans together in a large bucket so every wall comes out exactly the same color.
  • Trim, fascia, soffits and doors are not included. Estimate them separately, usually in a semi-gloss.

Next step

Prime bare wood and repairs

New siding, bare wood and patched stucco need primer before the finish coats.

Calculate primer

Also useful

Check the coverage you're getting

After the first wall, compare the area painted with the paint used to see if your estimate holds.

Check paint coverage

How to measure

  1. Walk around the house with a tape or measuring wheel and add up the length of every wall you'll paint. Include the garage if it gets the same color.
  2. Measure wall height from the foundation line (where the siding starts) to the eaves. Allow about 9–10 ft per story.
  3. Count the gable ends — the triangles under the roof at each end of a gable roof. Measure the width of the wall below each one and either the roof pitch or the height from eaves to peak.
  4. Count doors and windows. Count a single garage door as about 6 doors' worth of area, or change the door size under Advanced options.

How the exterior paint calculation works

Walls          = perimeter × wall height
Gable height   = (gable width ÷ 2) × pitch ÷ 12
Gables         = number × gable width × gable height ÷ 2
Paintable area = walls + gables − doors − windows
Paint          = paintable area × siding factor × coats ÷ coverage
Buy            = paint × (1 + extra %), rounded up to buckets and cans

Unfold the house and its walls become one long rectangle — perimeter by height. Gable ends sit on top as triangles, half of width times height. A 6/12 pitch rises 6 in for every 12 in across, so a 30 ft gable is 7.5 ft tall at the peak.

Siding texture matters more outside than in. Lap siding has board edges and drip lines (×1.1), cedar shingles and shakes are rough-sawn with deep butts (×1.25), and stucco or brick is rough and porous (×1.4). The factor turns the flat outline into the surface the paint actually has to cover.

The final step rounds to containers, preferring 5-gallon buckets when they leave less paint over. Buckets are usually cheaper per gallon and keep the color consistent.

Worked example

A single-story house with a 140 ft perimeter, 10 ft walls, two 30 ft gable ends at 6/12, two doors, ten windows and lap siding. Two coats.

  1. Walls: 140 × 10 = 1,400 sq ft
  2. Gables: 15 × 6 ÷ 12 = 7.5 ft high; 2 × 30 × 7.5 ÷ 2 = 225 sq ft
  3. Openings: (2 × 21) + (10 × 15) = 192 sq ft
  4. Paintable: 1,400 + 225 − 192 = 1,433 sq ft × 1.1 lap siding = 1,576 sq ft
  5. Paint: 1,576 × 2 ÷ 350 = 9.01 gallons; with 10% extra = 9.91 gallons

Buy 10 gallons — two 5-gallon buckets. Trim, fascia and doors are extra, usually a gallon or two of semi-gloss.

How much extra to allow

Outside, more paint is lost to wind, sprayer overspray, and texture that eats more than you'd expect. Keep the extra higher if you spray.

SituationAllow
Brush and roller, smooth or lap siding10%
Rough siding, shakes, stucco15%
Airless sprayer20–30%

Reading your result

The highlighted number is what to buy; the note under it shows the bucket and can split. When you're between sizes, the calculator also shows the all-bucket option.

Mix all the cans together in one large bucket before you start ("boxing"), so no wall ends up a slightly different shade.

If the 'With extra' figure is just over a bucket, one extra gallon can is usually cheaper than a second bucket.

Assumptions

  • Coverage of 350 sq ft per gallon on a smooth surface, adjusted by the siding factor. Many exterior labels list 250–400; use yours under Advanced options.
  • Doors are 21 sq ft and windows 15 sq ft. Large picture windows, sliders and garage doors are worth adjusting for.
  • The siding is sound and already painted. Bare wood, new stucco and chalky old paint need primer first.
  • Soffits, fascia, trim and porch ceilings aren't included.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Second stories, steep lots and anything that needs extension ladders or scaffolding are where pros earn their fee — and where most DIY falls happen.
  • Homes built before 1978 may have lead paint. Scraping and sanding must follow lead-safe practices; get it tested first.
  • Peeling down to bare wood across large areas usually points to moisture problems that paint won't fix.

Frequently asked questions

How much paint do I need for the outside of a house?

A typical single-story house with about 1,500 sq ft of siding needs roughly 9–11 gallons for two coats. Two-story homes often need 15–20. The real number depends on the perimeter, height and siding texture.

Does siding type change how much paint I need?

Yes. Rough and porous surfaces have more real surface area and soak paint in. Plan on about 10% more for lap siding, 25% for shingles and shakes, and 40% for stucco or brick compared with a smooth wall.

How do I calculate the area of a gable end?

Multiply the width of the wall below it by the gable's height and divide by two. If you know the roof pitch, the height is half the width times the pitch over 12: a 30 ft gable at 6/12 is 15 × 0.5 = 7.5 ft tall.

Is one coat enough on exterior siding?

Only when repainting the same color over sound, well-bonded paint. Color changes, faded or chalky siding and bare patches need two coats for even color and full weather protection.

More painting calculators

All painting