Skip to content
MeasureToBuy

Deck Stain Calculator

Enter the deck size (or any wood area), the type of stain, the surface and the number of coats. You'll get the gallons of stain and the cans to buy.

Measurements

Measure by

Rough guide: rail length × rail height for each side you stain.

Stain type
Wood surface
Coats
Extra

Rule of thumb for gaps, end grain and spillage.

Your estimate

You need about 1.7 gallons of stain — buy 2 × 1 gal.

252 sq ft × 2 coats at 250 sq ft/gal first coat.

Area
252 sq ft
First coat coveragelow end of the published range
250 sq ft/gal
Second coat coverage
500 sq ft/gal
Extra
10%
Stain needed
1.7 gal
Buy
2 × 1 gal
  • Second coats of penetrating stain go on thinner and cover more, which is why the second-coat rate is higher. Follow the can — some stains are one coat only.
  • Do a test patch: weathered, dry wood can drink twice as much as new planed boards.

Next step

Building or re-boarding the deck?

Count deck boards, joists and fasteners.

Deck calculator

Also useful

Staining a fence too?

Measure the fence, then enter both faces here as a known area.

Fence calculator

How to measure

  1. Measure the deck's length and width for the floor boards.
  2. Estimate railings, stairs and skirting: rail length × height for each face you'll stain.
  3. For fences or siding, choose "Known area" and enter the face area (both sides of a fence if you're doing both).

How the deck stain calculation works

Gallons = area ÷ first-coat coverage + area ÷ second-coat coverage (if 2 coats)
To buy  = gallons × (1 + extra), packed into 5 gal and 1 gal cans

Penetrating stain soaks into bare wood on the first coat and much less on the second, so the second coat covers more. BEHR lists its semi-transparent waterproofing stain at 250–300 sq ft per gallon for the first coat and 500–600 for the second.

Rough-sawn and weathered wood soaks up far more: Cabot lists its semi-transparent stain at 150–250 sq ft per gallon on rough wood versus 400–600 on smooth. The calculator uses the low end of each range.

Worked example

A 16 × 12 ft deck plus 60 sq ft of railings, two coats of semi-transparent stain on smooth boards, 10% extra.

  1. Area: 16 × 12 + 60 = 252 sq ft
  2. First coat: 252 ÷ 250 = 1.01 gal; second coat: 252 ÷ 500 = 0.50 gal
  3. Total: 1.51 gal × 1.10 = 1.66 gal

Buy two 1-gallon cans.

How much extra to allow

Board gaps, end grain and drips use stain you don't see on the surface. Weathered wood can use much more than new boards.

SituationAllow
New, planed boards10%
Old or weathered wood15% or test first

Reading your result

Buy the cans shown. Keep all cans from one batch, or mix them together, so the colour matches across the deck.

Some stains are one-coat products — follow the label over this estimate.

Assumptions

  • Semi-transparent smooth: BEHR Premium Semi-Transparent Waterproofing Stain & Sealer. Semi-transparent rough: Cabot. Solid colour: BEHR Premium Solid Color House & Fence (200–400 first coat, 250–500 second). Clear sealer: Thompson's WaterSeal (150–400).
  • Low end of each range, so you won't run short.
  • Extra allowance is a rule of thumb.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

Frequently asked questions

How much deck stain do I need?

Divide the area by the can's coverage for each coat. For 250 sq ft with a semi-transparent stain at 250 sq ft per gallon for the first coat and 500 for the second, you need about 1.5 gallons.

Does a second coat of stain take as much as the first?

No. With penetrating stains the second coat goes on thinner — BEHR lists 500–600 sq ft per gallon for the second coat versus 250–300 for the first.

Why does rough wood need more stain?

Rough-sawn and weathered surfaces have more surface area and absorb more. Cabot lists 150–250 sq ft per gallon on rough wood and 400–600 on smooth.

More painting calculators

All painting