Skip to content
MeasureToBuy

Backsplash Tile Calculator

Enter each counter run, the backsplash height and any area you won't tile. The calculator gives tiles and boxes for individual tile, or sheets for mosaics, plus grout and outlet extenders.

Measurements

Wall length above the counter, end to end.

Counter to the underside of the upper cabinets — 18 in (450 mm) is standard.

A window, or the wall behind the range if it won't be tiled. Width × height.

Tile type

Subway, square or plank tile

1/16 in (1.5 mm) is typical for subway tile.

Waste allowance

Backsplashes have many short cuts at cabinet ends, outlets and windows.

On the box label. Leave as is if buying loose tiles.

Each needs notched tiles and a box extender.

Advanced optionscoverage, sizes, custom values

Used for the grout estimate.

Your estimate

You need 128 tiles — 4 boxes.

10 ft of counter × 18 in high = 15 sq ft, plus 10% waste.

Counter run
10 ft
Backsplash height
18 in
Gross area
15 sq ft
Area to tile
15 sq ft
Tile size
3 in × 6 in
Tiles to cover the area7.76 tiles per sq ft with joints
117 tiles
Waste allowance
10%
Tiles to buy
128 tiles
Boxes of 4020 sq ft of tile
4 boxes

Grout and outlets

Grout, approximately1 × 10 lb bag, or a premixed tub
1.4 lb
Outlet box extendersbrings each device flush with the tile
3 extenders
  • Turn off the power before removing cover plates. Longer screws or box extenders bring outlets out to the new tile face.
  • Run tile under the upper cabinets by about ¼ in so the edge is hidden; finish exposed ends with bullnose or metal edge trim.

Next step

Price thinset and grout too

Add setting materials to see the full material cost of a tile job.

Estimate tile cost

Also useful

Tiling a bathroom next?

Estimate the floor and the tub or shower walls together, each with its own tile.

Bathroom tile calculator

How to measure

  1. Measure each wall section above the counter end to end — main wall, side wall, island back — and add each as its own section.
  2. Measure the height from the countertop to the underside of the upper cabinets. 18 in is standard; full-height areas behind a range are often taller.
  3. Work out the area of anything you won't tile: a window (width × height) or the wall behind a range hood if it stays painted.
  4. Count outlets and switches in the backsplash area.

How the backsplash tile calculation works

Area     = Σ run lengths × height − area left untiled
Tiles    = area ÷ ((tile w + joint) × (tile h + joint)) × (1 + waste %), rounded up
Sheets   = area ÷ sheet area × (1 + waste %), rounded up
Boxes    = tiles (or sheets) ÷ per box, rounded up

A backsplash is a long, narrow strip of wall, so every section shares one height. Windows and painted areas are subtracted before counting tile.

Individual tiles include one grout joint each way in their footprint. Mosaic sheets are made to butt at the same joint as the pieces inside them, so a 12 × 12 in sheet covers one square foot.

Backsplashes have a lot of short cuts at cabinet ends, outlets and windows, so 10% waste is a minimum.

Worked example

A 10 ft counter with an 18 in backsplash in 3 × 6 in subway tile, 1/16 in joints, 40 tiles per box, 10% waste.

  1. Area: 10 × 1.5 = 15 sq ft
  2. Tile with joint: 3.0625 × 6.0625 = 18.57 sq in = 0.129 sq ft
  3. Tiles: 15 ÷ 0.129 = 116.3 → 117 tiles
  4. With 10% waste: 116.3 × 1.1 = 128.0 → 128 tiles
  5. Boxes: 128 ÷ 40 = 3.2 → 4 boxes

Buy 4 boxes (160 tiles). As 12 × 12 in mosaic sheets the same wall takes 17 sheets.

How much extra to allow

Small surfaces and many interruptions make backsplash waste higher than a floor, even with a straight layout.

SituationAllow
Straight or running bond, few outlets10%
Many outlets, windows or short sections15%
Herringbone or chevron20%
Mosaic sheets10% — sheets cut cleanly along the mesh

Reading your result

The headline is tiles (or sheets) with the box count. Buy by boxes unless your store sells single pieces.

Outlet box extenders bring each outlet flush with the new tile face. You'll need one per outlet or switch.

A 10 lb bag of grout, or a small premixed tub, covers most backsplashes.

Assumptions

  • Every section is the same height. If one part runs taller (behind a range), add it as a separate section and adjust its length to give the right area.
  • Grout for mosaics assumes 1/16 in joints between the pieces at the piece size you enter.
  • Edge trim (bullnose, pencil or metal) isn't counted. Measure exposed ends separately.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Moving or adding outlets in the backsplash is electrical work — use a licensed electrician if you're not sure.
  • Natural stone and glass mosaics need specific thinset and sealing. Follow the manufacturer's instructions.

Frequently asked questions

How many subway tiles do I need per square foot?

About 7.8 tiles per sq ft for 3 × 6 in subway with 1/16 in joints, before waste.

How high is a standard backsplash?

18 in from the countertop to the upper cabinets. Some homes have 15–20 in; measure yours.

Do I tile behind the stove?

Usually yes, often up to the range hood. If you're leaving it painted or using a stainless panel, enter it as untiled area.

How many mosaic sheets do I need?

A 12 × 12 in sheet covers 1 sq ft, so a 15 sq ft backsplash needs 15 sheets, or 17 with 10% waste.

More flooring & tile calculators

All flooring & tile