Skip to content
MeasureToBuy

Rebar Calculator

Enter the slab size, bar size and grid spacing from your plans. You'll get the number of stock bars to buy, lap splices, total length, weight and the intersections to tie — or the welded wire mesh sheets instead.

Structural sizes — footings, framing, stairs — are governed by local building codes and site conditions. Use this for material planning, and confirm sizes with your building department or an engineer.

Measurements

Reinforcement
Bar size
Grid spacing

Use the spacing on your plans. Common values are shown; they are not a design recommendation.

How far the bars stop short of the slab edge.

Bar length you'll buy
Advanced optionscoverage, sizes, custom values
bar diameters

A common rule of thumb, not a code value — lap lengths depend on bar size, grade and concrete strength. Your engineer's drawings govern.

Your estimate

You need 16 bars of #4 rebar, 20 ft long.

22 runs at 18 in each way = 317 ft of bar including laps.

Slab
240 sq ft
Total bar length
317 ft
#4 bars to buy
16 bars
Weight
212 lb

Grid

Bars along the length19.5 ft each
8 bars
Bars along the width11.5 ft each
14 bars
Lap splicesevery run fits one bar
0 splices
Intersections to tie
112 intersections
  • The bar count assumes offcuts are used for shorter runs. Buy one or two spares if you can't reuse them.
  • Support the grid on chairs or dobies so it sits in the slab, not on the ground.

Next step

Working out the concrete?

The slab calculator uses the same length and width for volume, bags and the gravel base.

Concrete slab calculator

How to measure

  1. Measure the slab inside the forms.
  2. Take the bar size and spacing from your plans or permit drawings.
  3. Set the edge distance — how far the grid stops short of the forms (3 in is common).
  4. Pick the stock length you'll buy: 20 ft bars mean fewer splices on large slabs, 10 ft bars fit in a car.

How the rebar calculation works

Bars one way   = floor((width − 2 × edge) ÷ spacing) + 1
Pieces per run = 1 + ceil((run − stock) ÷ (stock − lap))  when run > stock
Cut length     = run + splices × lap
Bars to buy    = Σ cut lengths ÷ stock length, rounded up
Weight         = total length × weight per foot

Bars run both ways across the slab. Each run that's longer than a stock bar is spliced, and every splice overlaps by the lap length, so long slabs use more steel than their dimensions suggest.

Weights are ASTM A615 nominal values: #3 0.376, #4 0.668, #5 1.043 and #6 1.502 lb per ft. Metric bars use steel at 7,850 kg/m³.

Worked example

A 20 × 12 ft slab, #4 bars at 18 in each way, 3 in from the edges, from 20 ft bars.

  1. Runs: 20 ft − 6 in = 19.5 ft and 12 ft − 6 in = 11.5 ft — both fit a 20 ft bar, so no splices
  2. Bars along the length: floor(138 ÷ 18) + 1 = 8; along the width: floor(234 ÷ 18) + 1 = 14
  3. Total: 8 × 19.5 + 14 × 11.5 = 317 ft ÷ 20 = 15.9 → 16 bars
  4. Weight: 317 × 0.668 = 212 lb; 8 × 14 = 112 intersections to tie

Buy 16 bars of #4 rebar, 20 ft long — about 212 lb of steel.

Reading your result

The bars-to-buy row is your order. Add tie wire and chairs (or dobies) to hold the grid at mid-depth.

If a run needs a splice, stagger the splices so they don't all line up across the slab.

Assumptions

  • Offcuts are reused for shorter runs; without that you may need a bar or two more.
  • Lap length defaults to 40 bar diameters, a common rule of thumb. ACI 318 and CRSI make lap length depend on bar size, steel grade, concrete strength and spacing — use the length on your drawings.
  • Spacing options are common values, not a design recommendation.
  • Wire mesh: 5 × 10 ft sheets overlapped 6 in each way.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Reinforcement for footings, foundation walls, structural slabs and anything carrying a building is specified by an engineer or the code tables your building department uses. This calculator counts steel for a layout you already have.

Frequently asked questions

How much does rebar weigh per foot?

#3: 0.376 lb, #4: 0.668 lb, #5: 1.043 lb, #6: 1.502 lb per foot (ASTM A615 nominal weights).

How much should rebar overlap?

It depends on the bar, steel grade and concrete. 40 bar diameters (20 in for #4) is a common rule of thumb, but the lap length on your plans governs.

How many rebar intersections do I need to tie?

A grid has one intersection per crossing — bars one way × bars the other way. Specs vary between tying every intersection and every other one.

Is wire mesh as good as rebar in a slab?

They do different jobs. 6 × 6 welded wire mesh mainly controls shrinkage cracks in light slabs; rebar adds more strength. Use what your plans call for.

More concrete & masonry calculators

All concrete & masonry