Skip to content
MeasureToBuy

How to Measure Roof Pitch: Rise, Angle & Percent Slope

Measure roof pitch from the attic, roof, gable end or plans, convert between rise per 12, degrees and percent, and see the IRC minimum pitch per roofing type.

Updated November 13, 2026

The short answer

Roof pitch is how many inches the roof rises for every 12 inches it runs horizontally, written as rise/12. A roof that climbs 6 in over a 12 in run is a 6/12 roof. You can measure it from the roof surface, from the attic, from the gable end or from plans, and then convert it to degrees or percent slope if a product or code uses those instead.

Pitch (rise per 12 in)  = rise ÷ run × 12
Angle                   = arctan(rise ÷ 12)
Percent slope           = rise ÷ 12 × 100
Pitch factor (area)     = √(1 + (rise ÷ 12)²)

The pitch factor is what turns a footprint into roof area. The roofing squares guide covers that step and the bundle count. This guide covers the part before it: getting the pitch right, and knowing what it means for the roofing material you can use.

Four ways to measure pitch

All four give the same number. Pick the one that keeps your feet on the ground.

  • From the attic. The safest method. Hold a level horizontally against the underside of a rafter, mark 12 in along the level from the rafter, then measure straight up from that mark to the rafter. That vertical distance in inches is the rise. The two faces of a rafter are parallel, so the underside gives the same slope as the roof surface.
  • On the roof. The same level-and-tape method, with the level resting on the roof surface. Only do this on a roof you can walk safely, with the right fall protection.
  • From the gable end. Stand square to the end wall. For a symmetric gable, the run is half the building width and the rise is how far the ridge sits above the top of the wall. Then pitch = 12 × rise ÷ run. A photo taken straight on works too: measure the rise and the half-width on the picture with a ruler and use the same formula. A photo taken at an angle distorts the result. If the roof surface starts above the top of the wall (raised-heel trusses), use the height difference and the horizontal distance between the same two points on the roof surface instead, not the wall line.
  • From plans. Drawings usually mark pitch with a small right-angle triangle, with the rise as a number over 12. If they don’t, use the gable end formula with the dimensions on the elevation.

Measure in more than one spot. An old roof can sag between rafters, and a single reading over a dip will be off. If your readings differ, use the rafter or truss line rather than the deck between them.

If you only have an angle

A phone inclinometer or a digital angle finder gives degrees, not rise/12. Convert with rise per 12 in = 12 × tan(angle). Round only for display: compare the unrounded pitch with any product or code limit. A 9° reading is about 1.9/12, which rounds to 2/12 but is below a 2/12 minimum. If your reading is within a few tenths of a limit, check it against a level-and-tape reading before you order.

AnglePitch
10°2.1/12
15°3.2/12
20°4.4/12
25°5.6/12
30°6.9/12
35°8.4/12
40°10.1/12
45°12/12

Pitch, angle and percent slope

Codes and manufacturers sometimes give a slope as a percent or in degrees. Percent slope is rise ÷ 12 × 100, so 12/12 is 100% and 45°:

PitchAnglePercent slope
1/124.8°8.3%
2/129.5°16.7%
3/1214.0°25.0%
4/1218.4°33.3%
5/1222.6°41.7%
6/1226.6°50.0%
7/1230.3°58.3%
8/1233.7°66.7%
9/1236.9°75.0%
10/1239.8°83.3%
11/1242.5°91.7%
12/1245.0°100%

Metric drawings often give pitch as a ratio of rise to run in the same unit (a 1:2 slope is 6/12) or as an angle in degrees. Use the angle row above, or work out rise ÷ run × 12.

Minimum pitch by roofing material

Pitch decides which roofing you may install. The 2021 International Residential Code, Chapter 9, sets a minimum slope for each covering. These are code minimums; your local building department adopts its own edition and may amend it, and a manufacturer can require a steeper roof or extra underlayment, so read the product instructions too.

Roof coveringIRC 2021 sectionMinimum pitch
Asphalt shinglesR905.2.22/12
Clay and concrete tileR905.3.22½/12
Metal roof shinglesR905.4.23/12
Mineral-surfaced roll roofingR905.5.21/12
SlateR905.6.24/12
Wood shinglesR905.7.23/12
Wood shakesR905.8.23/12
Metal panels, lapped seams, no sealantR905.10.23/12
Metal panels, lapped seams, with applied lap sealantR905.10.2½/12
Standing-seam metal panelsR905.10.2¼/12

For asphalt shingles, the code says to use them only on slopes of 2/12 or more and to use two layers of underlayment from 2/12 up to 4/12. A 3/12 roof can therefore take shingles, but you need to buy and lay the second layer of underlayment. Clay and concrete tile also needs double underlayment from 2½/12 up to 4/12.

This table covers pitched roofs only. Flat and low-slope membrane roofs have their own rules, and so do roofs that mix pitches. If your measurement lands near a limit, ask the building department or the manufacturer before you order.

Worked example: from a reading to a roof area

From the attic, the rise on a 12 in level mark is 7 in. The house is 40 ft × 30 ft including overhangs, a simple gable.

Pitch        7 in rise ÷ 12 in run = 7/12
Angle        arctan(7 ÷ 12) = 30.3°
Percent      7 ÷ 12 × 100 = 58.3%
Pitch factor √(1 + (7 ÷ 12)²) = √1.3403 = 1.1577 (the calculator shows 1.158)
Roof area    1,200 sq ft × 1.1577 = 1,389 sq ft
Squares      1,389 ÷ 100 = 13.9

For the gable end method, take a different house: the walls are 28 ft apart and the ridge sits 7 ft above the top of the wall. The run is half the width, 14 ft, so pitch = 12 × 7 ÷ 14 = 6/12.

Why it is worth reading twice: had the first house read 6/12 instead of 7/12, the same 1,200 sq ft footprint would give 1,200 × 1.118 = 1,342 sq ft, or 13.4 squares. One inch of rise moves the roof area by about 47 sq ft, roughly half a square.

Common measuring mistakes

  • Using the full width as the run. For the gable end formula the run is half the span, not the whole width.
  • Letting the level droop. A level that is not truly horizontal changes the rise you read off. Check the bubble before you measure.
  • Measuring the rise from the wrong mark. The 12 in is measured along the horizontal level, and the rise is measured straight up (plumb) from that point to the roof.
  • Assuming one pitch. Porch roofs, additions and dormers are often at different pitches from the main roof. Measure each section and calculate it separately.
  • Angling the photo. A photo not taken square to the gable end gives a wrong ratio.

In metric

The figures above are in US units, as the manufacturers and standards give them. Here they are in metric, converted with the same factors the calculators use. Switch any calculator to m · cm to work in metric from the start.

Figure in this guideUSMetric
Run, 12 in12 inches≈ 305 mm
Rise, 6 in (a 6/12 roof)6 inches≈ 152 mm

Pitch is a ratio, so it does not change with units: a 6/12 roof rises 6 units for every 12 units of run, whether those are inches or millimetres.

Calculate it for your project

The Roof Pitch Calculator does the conversions above from rise and run, building width and ridge height, an angle or a percent slope. With the pitch in hand, the Roof Area Calculator turns a footprint into sloped roof area, and the Roofing Calculator goes on to squares, bundles and accessories. The Shingle Calculator converts squares to bundles. Planning the whole job? Use the roof replacement planner. Pitch also feeds the gutter sizing guide.