What Size Gutters Do I Need? Sizing Gutters & Downspouts
Size gutters from roof area, pitch and rainfall intensity, compare 5 in and 6 in K-style ratings, and count downspouts and hangers.
Updated October 18, 2026
The short answer
Multiply the roof area that drains into a gutter by a pitch factor and by your local rainfall intensity, then compare it with the gutter’s rated area:
Adjusted area = roof area × pitch factor × rainfall (in per hour) ≤ 5,520 for 5 in K-style, 7,960 for 6 in K-style
The method and figures below are from This Old House; the City of Naples, Florida and Fine Homebuilding describe the same calculation.
Step 1: the roof pitch factor
Steeper roofs catch more wind-driven rain, so their area counts for more:
| Roof pitch | Factor |
|---|---|
| Flat to 3/12 | 1.0 |
| 4/12 to 5/12 | 1.05 |
| 6/12 to 8/12 | 1.1 |
| 9/12 to 11/12 | 1.2 |
| 12/12 or steeper | 1.3 |
Some installers use slightly different factors (one lists 1.15 for 6/12), so ask which table yours uses.
Step 2: your rainfall intensity
This is the rate of the heaviest short bursts of rain in your area, in inches per hour. NOAA’s Atlas 14 precipitation-frequency server (hdsc.nws.noaa.gov) gives it for any US location; building departments and gutter installers know the local figure too. The City of Naples example uses 7.8 in per hour; Fine Homebuilding’s uses 6.6.
Step 3: compare with the gutter’s rating
| Gutter | Rated area |
|---|---|
| 5 in K-style | 5,520 sq ft |
| 6 in K-style | 7,960 sq ft |
| 5 in half-round | 2,500 sq ft |
| 6 in half-round | 3,840 sq ft |
If the adjusted area is larger, step up a size or add downspouts so each length of gutter drains less roof.
Downspouts
A rule of thumb from This Old House: about 1 sq in of downspout opening for every 100 sq ft of roof. That makes a 2 × 3 in downspout good for about 600 sq ft and a 3 × 4 in for up to 1,200 sq ft (3 in round about 706, 4 in round up to 1,255). Gutters that run 60 ft or longer should have at least two outlets.
Worked examples
City of Naples 1,000 sq ft × 1.1 (6/12) × 7.8 in/hr = 8,580 → more than 5,520: 5 in K-style is too small
8,580 ≤ 7,960? No — add a downspout or split the run, or go larger
One eave 600 sq ft × 1.1 × 6 in/hr = 3,960 → 5 in K-style is enough
Downspouts 600 ÷ 600 = 1 × 2 × 3 in; a 40 ft run needs only one outletHangers and slope
Hang gutters every 24 in, or every 18 in where heavy snow and ice load them (City of Detroit gutter guidance; Amerimax lists one hanger per 24 in). Slope them about ¼ in per 10 ft toward the downspouts.
In metric
The figures above are in US units, as the manufacturers and standards give them. Here they are in metric, converted with the same factors the calculators use. Switch any calculator to m · cm to work in metric from the start.
| Figure in this guide | US | Metric |
|---|---|---|
| 5 in K-style gutter | 5 inches | ≈ 127 mm |
| 6 in K-style gutter | 6 inches | ≈ 152 mm |
| Rainfall, 1 in per hour | 1 inch | ≈ 25.4 mm |
| Rated area, 5 in gutter (sq ft) | 5,520 square feet | ≈ 513 m² |
| Rated area, 6 in gutter (sq ft) | 7,960 square feet | ≈ 740 m² |
The formula uses rainfall in inches per hour. For a rainfall rate in mm per hour, divide it by 25.4 first, then multiply the roof area in m² by the pitch factor and that rate, and compare the result with the rated areas in m² above. The metric ratings are rounded; if your result is within about 1% of one, compare in square feet against the original rating before choosing a size.
Calculate it for your project
The Gutter Calculator runs this check for each run and counts gutter length, hangers and downspouts. Not sure of the roof area? Start with the Roof Area Calculator.