Skip to content
MeasureToBuy

Roof Pitch Calculator

Enter whichever measurement you have: rise and run, building width and ridge height, an angle, or a percent slope. You get the pitch in inches of rise per 12, plus the angle in degrees, the percent slope and the multiplier that turns a footprint into roof area.

Footprint-and-pitch estimates suit simple gable and hip roofs. Roofs with dormers, multiple pitches or many valleys should be measured by a roofer.

Measurements

How far the roof climbs, measured straight up from the level.

The horizontal distance along the level. 12 in is the usual.

Your estimate

Your roof pitch is 6/12 — a 26.6° slope.

That is 50% slope. Multiply a roof's footprint by 1.118 to get its surface area.

Rise
6 in
Run
12 in
Pitch, inches of rise per 12 in
6
Angle
26.6 degrees
Percent slope
50 percent
Roof area multiplierFootprint × this = roof area
1.118

Asphalt shingles (2021 IRC)

Meets the IRC minimum?R905.2.2
Yes
  • Pitch is the inches of rise for every 12 inches of horizontal run, so 6/12 means 6 in of rise over 12 in of run.
  • Code minimums differ by roof covering. The roof pitch guide lists them for tile, metal, slate and wood too.
  • This checks the model code's minimum only. Local codes and the shingle maker's instructions can be stricter, so check both before you buy.

Next step

Turn the pitch into roof area

The closest pitch to choose there is 6/12. Add the building's length, width and overhang to get roof area and squares.

Roof area calculator

Also useful

Planning the shingles?

Use the pitch with the footprint to get squares, bundles, underlayment and accessories in one place.

Roofing calculator

How to measure

  1. Rise and run: hold a level horizontally against a rafter or the roof, mark 12 in along it, then measure straight up from that mark to the roof. That vertical distance is the rise, and 12 in is the run. The attic is the safest place to do it.
  2. Building width and ridge height: at the gable end, measure the width of the building wall to wall (outside faces, not counting the overhangs) and how high the ridge sits above the top of the walls. The run is half the width. This works only when the ridge is in the centre and the roof surface starts at the top of the wall; if the ridge is off to one side, or the roof starts above the wall (raised-heel trusses), measure rise and run between two points on one roof face instead.
  3. Angle: lay a phone inclinometer or a digital angle finder along a common rafter, or along the line of steepest slope on one roof face (from the eave straight up to the ridge), and read the angle from horizontal. Held parallel to the ridge it reads 0°, and along a hip or valley rafter it reads too low.
  4. Percent slope: take it from the plans, where it is usually rise ÷ run × 100.

How the roof pitch calculation works

Pitch      = 12 × rise ÷ run
Gable end  = 12 × ridge ÷ half-width
Angle in   = 12 × tan(angle)
Percent in = 12 × percent ÷ 100
Angle      = arctan(pitch ÷ 12)
% slope    = pitch ÷ 12 × 100
Multiplier = √(1 + (pitch ÷ 12)²)

Pitch is how many inches the roof climbs for every 12 inches it runs horizontally. A 6/12 roof rises 6 in per foot. Every other way of measuring a roof is the same triangle described differently, so the calculator converts between them.

A sloped roof is longer than the ground it covers. The roof area multiplier is the sloped length for each foot of run, so multiplying a footprint (including the overhangs) by it gives the surface area.

Worked example

A 7 in rise measured over a 12 in run in the attic.

  1. Pitch: 12 × 7 ÷ 12 = 7, so 7/12
  2. Angle: arctan(7 ÷ 12) = 30.3°
  3. Percent slope: 7 ÷ 12 × 100 = 58.3%
  4. Roof area multiplier: √(1 + (7 ÷ 12)²) = 1.158

The roof is 7/12, a 30.3° slope or 58.3% slope. A 1,200 sq ft footprint becomes 1,200 × 1.1577 (the unrounded 1.158) = 1,389 sq ft of roof, which is 13.9 squares.

Reading your result

Asphalt shingles need a pitch of 2/12 or more under the 2021 IRC, with two layers of underlayment from 2/12 up to 4/12. Local codes and shingle makers can be stricter.

Use the roof area multiplier on the footprint including the overhangs, or enter the pitch in the Roof Area Calculator.

The Roof Area and Roofing calculators offer whole-number pitches, so choose the closest one to your result.

Assumptions

  • The roof has one pitch. Porch roofs, dormers and additions can differ, so measure each section separately.
  • Pitch means rise per 12 in of run, the US roofing convention, not rise over the full span.
  • The level is held truly horizontal and the rise is measured straight up, not along the slope.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Measure from the attic or the ground where you can. Don't climb a roof you aren't equipped for, and call a roofer for steep, wet or damaged roofs.

Frequently asked questions

How do I find my roof pitch?

Hold a level against a rafter, mark 12 in along it, and measure straight up to the roof. That rise is the pitch, so a 6 in rise is 6/12. Measuring from the attic avoids climbing.

What is a 6/12 roof pitch in degrees?

About 26.6°, or a 50% slope. For comparison, 4/12 is 18.4° and 12/12 is exactly 45°.

How do I convert degrees to roof pitch?

Multiply the tangent of the angle by 12. A 30° roof is 12 × tan(30°) = 6.9, so about 7/12.

What is the minimum roof pitch for asphalt shingles?

The 2021 International Residential Code allows asphalt shingles on slopes of 2/12 or more, and asks for two layers of underlayment from 2/12 up to 4/12. Local codes and the shingle maker can be stricter.

More roofing, siding & gutters calculators

All roofing, siding & gutters