How to Calculate Square Footage (Rooms, L-Shapes & Odd Spaces)
Measure any room or area in square feet: rectangles, L-shaped rooms, triangles and circles, with worked examples and common mistakes.
Updated October 7, 2026
The short answer
Square footage is length times width, with both measurements in feet. A room 12 ft wide and 14 ft long is 12 × 14 = 168 sq ft. Any space that isn’t a plain rectangle gets split into rectangles, triangles and circles; you work out each piece and add them up.
Every flooring, tile, paint and sod estimate starts from this number, so it pays to get it right. The Square Footage Calculator handles the shapes below and converts the units for you.
Rectangles and feet-and-inches
Area = length × width
The only catch is inches. Convert them to decimal feet by dividing by 12 before multiplying. A room that measures 12 ft 6 in by 10 ft 9 in becomes:
- 12 ft 6 in = 12 + 6 ÷ 12 = 12.5 ft
- 10 ft 9 in = 10 + 9 ÷ 12 = 10.75 ft
- Area: 12.5 × 10.75 = 134.4 sq ft
If you’re measuring several rooms, the Room Area Calculator keeps a running total so you round once at the end rather than per room.
L-shaped rooms
Split an L into two rectangles with one imaginary line, measure each, and add. It doesn’t matter which way you cut, as long as no floor is counted twice.
Example: a room is 20 ft across the full back wall and 16 ft deep on one side, but the front 6 ft is only 8 ft wide.
- Rectangle A (the full-width part): 20 × 10 = 200 sq ft
- Rectangle B (the narrow leg): 8 × 6 = 48 sq ft
- Total: 200 + 48 = 248 sq ft
Check it by subtraction: the bounding box is 20 × 16 = 320 sq ft, and the missing corner is 12 × 6 = 72 sq ft. 320 − 72 = 248 sq ft. When both methods agree, your measurements are consistent. The same approach works for T- and U-shaped rooms; you just end up with three rectangles.
Triangles, circles and bays
Triangles
Area = base × height ÷ 2
The height is measured at a right angle to the base, not along the sloping side. A corner cut off at 45° with a 10 ft base and a 6 ft depth is 10 × 6 ÷ 2 = 30 sq ft. Angled walls, gable ends and wedge-shaped garden beds all work this way.
Circles and half-circles
Area = π × radius² (radius = diameter ÷ 2)
An 8 ft round patio has a 4 ft radius: 3.1416 × 4 × 4 = 50.3 sq ft. A half-round bay window with the same 8 ft opening is half that, 25.1 sq ft. Add it to the rectangle of the main room.
Irregular spaces: the offset method
For a curved border or a wandering lawn edge, run a straight baseline along one side and measure out from it at regular intervals, square to the baseline. Then treat each gap between offsets as a trapezoid:
Area ≈ interval × (first ÷ 2 + middle offsets + last ÷ 2)
Example: a 20 ft baseline with offsets every 5 ft of 6, 8, 9, 7 and 5 ft.
- Half the end offsets: 6 ÷ 2 + 5 ÷ 2 = 5.5
- Middle offsets: 8 + 9 + 7 = 24
- Area: 5 × (5.5 + 24) = 147.5 sq ft
Closer intervals give a more accurate result on tight curves. For lawns, the Lawn Area Calculator is built for this kind of shape.
Converting between units
Products are sold in different units. Carpet is often priced per square yard, land per acre, and imported tile per square metre.
| From | To | Do this |
|---|---|---|
| sq in | sq ft | ÷ 144 |
| sq ft | sq yd | ÷ 9 |
| sq ft | m² | × 0.0929 |
| m² | sq ft | × 10.764 |
| sq ft | acres | ÷ 43,560 |
So the 168 sq ft room is 168 ÷ 9 = 18.7 sq yd, or 168 × 0.0929 = 15.6 m². Going the other way, a 4 m × 3.5 m room is 14 m², which is 14 × 10.764 = 150.7 sq ft. Note that a square yard is 9 sq ft, not 3: the factor of 3 applies in each direction.
Measuring tips
- Measure wall to wall at floor level, not along the baseboard top. Baseboards come off or sit over the flooring edge, and walls aren’t always plumb.
- Measure both ends of each wall. Rooms are rarely perfectly square. Use the larger number.
- Include closets and alcoves if the new material continues into them, as separate rectangles.
- Round up to the next inch, not the next foot. Rounding every dimension up a full foot can add 15% or more to a small room.
- Sketch the room and write each measurement on the drawing. It makes splitting shapes, and spotting a missed section, much easier.
For walls rather than floors, the method is the same but uses perimeter × height. The Wall Area Calculator handles that, including door and window openings.
Common mistakes
- Reading inches as decimals. 12 ft 6 in is 12.5 ft, not 12.6 ft. In the example above, typing 12.6 × 10.9 gives 137.3 sq ft instead of 134.4: about 3 sq ft too much, and the error grows with room size.
- Mixing units in one formula. Multiplying feet by inches gives a meaningless number. Convert everything to feet first.
- Double-counting overlaps when splitting an L or T. Draw the dividing line and measure each piece only up to it.
- Adding waste to the area. Square footage is the actual floor. Waste belongs in the material estimate, and the right amount depends on the product; see how much waste to add for flooring.
In metric
The figures above are in US units, as the manufacturers and standards give them. Here they are in metric, converted with the same factors the calculators use. Switch any calculator to m · cm to work in metric from the start.
| Figure in this guide | US | Metric |
|---|---|---|
| Room width, 12 ft | 12 feet | ≈ 3.66 m |
| Room length, 14 ft | 14 feet | ≈ 4.27 m |
| Room area, 168 sq ft | 168 square feet | ≈ 15.6 m² |
| One square foot | 1 square foot | ≈ 0.0929 m² |
| One inch | 1 inch | ≈ 25.4 mm |
Calculate it for your project
Enter your dimensions in feet and inches or metres in the Square Footage Calculator and it will add up the shapes and convert the result. When you’re ready to buy material, carry that area into the Flooring Calculator to get a box count.