Skip to content
MeasureToBuy

Drywall Estimating: Sheets, Mud, Tape & Screws for a Room

Estimate drywall sheets, joint compound, tape and screws for a room, with USG and National Gypsum figures and IRC screw spacing.

Updated October 18, 2026

The short answer

Measure the board area (walls less doors and windows, plus the ceiling), divide by the sheet size and add about 10% for offcuts. For finishing, USG puts it at roughly two 4.5-gallon pails of all-purpose compound per 1,000 sq ft; plan about 370 ft of tape and roughly one screw per square foot.

Counting sheets

Wall board    = 2 × (length + width) × height − doors − windows
Ceiling board = length × width
Sheets        = board × (1 + waste) ÷ sheet area   (walls and ceiling separately)

Count walls and ceiling separately: ceilings are usually hung with the longest sheets you can lift, and offcuts from one rarely fit the other. 4 × 8 ft sheets (32 sq ft) are easiest to carry; 4 × 12 ft (48 sq ft) means fewer joints to finish.

Joint compound

USG says finishing 1,000 sq ft of wallboard takes about two 4.5-gallon pails of its UltraLightweight All Purpose compound, and that other USG ready-mix compounds are similar. National Gypsum’s ProForm guide gives 123–140 lb of ready-mix per 1,000 sq ft. Our calculator uses 0.137 lb per sq ft, the top of that range. Heavy skim coats and butt joints use more.

Tape

Paper tape runs about 370 ft per 1,000 sq ft of board (National Gypsum ProForm lists 375). Inside corners take tape too; outside corners take corner bead, bought by the length.

Screws and spacing

The IRC sets maximum fastener spacing for gypsum board (Table R702.3.5). For ½ in board on 16 in framing, as shown in local building department copies of the table:

WhereScrewsNails
Ceilings12 in on center7 in on center
Walls16 in on center8 in on center

At those spacings a 4 × 8 sheet takes roughly 28–35 screws, which is about one per square foot. Walls on 24 in framing need screws every 12 in, and a footnote requires tighter spacing on garage ceilings under living space — check your adopted code.

Worked example: a 14 × 12 ft room

Walls     2 × (14 + 12) × 8 = 416 sq ft − 1 door (21) − 2 windows (30) = 365 sq ft
Ceiling   14 × 12 = 168 sq ft
Sheets    365 × 1.10 ÷ 32 = 12.5 → 13;  168 × 1.10 ÷ 32 = 5.8 → 6;  19 sheets of 4 × 8
Compound  533 × 0.137 = 73 lb → 2 buckets
Tape      533 × 0.37 = 197 ft → 1 roll of 500 ft
Screws    about 533

After the drywall

New board and compound absorb paint unevenly, so they need a full coat of primer before the finish coats.

In metric

The figures above are in US units, as the manufacturers and standards give them. Here they are in metric, converted with the same factors the calculators use. Switch any calculator to m · cm to work in metric from the start.

Figure in this guideUSMetric
Sheet width, 4 ft4 feet≈ 1.22 m
Sheet length, 8 ft8 feet≈ 2.44 m
Sheet area, 32 sq ft32 square feet≈ 2.97 m²
Room length, 14 ft14 feet≈ 4.27 m
Room width, 12 ft12 feet≈ 3.66 m
Compound pail, 4.5 gal4.5 gallons≈ 17 L
Compound, per 1,000 sq ft1,000 square feet≈ 93 m²
Tape, 370 ft370 feet≈ 113 m

Calculate it for your project

The Drywall Calculator does the sheets and finishing for one room. The finish-a-room planner carries on through primer, paint, baseboard and caulk.