How to measure
- Subfloor: measure the floor's length and width to the outside of the rim joists.
- Walls: add up the length of every wall you're sheathing and measure the wall height from the bottom of the sill to the top plate. Subtract large openings only if you'll frame around them rather than cutting them out.
- Roof: use the sloped roof area, not the footprint. The Roof Area Calculator works it out from the footprint and pitch.
- Pick the sheet size. 4 × 9 and 4 × 10 sheets cover taller walls in one piece and cut down on blocking.
How the plywood calculation works
Subfloor area = length × width Wall area = total wall length × height − openings Roof area = sloped roof area Sheets = area × (1 + waste) ÷ sheet area, rounded up
Each application reduces to an area. Dividing by the sheet area (32 sq ft for a 4 × 8) gives the minimum number of sheets; waste covers cut-offs at edges, stair openings, hips and valleys.
Rounding happens once, at the end, so a total of 6.6 sheets becomes 7 — not one extra sheet per wall.
Worked example
A 16 × 12 ft subfloor with 4 × 8 sheets and 10% waste.
- Area: 16 × 12 = 192 sq ft
- With 10% waste: 192 × 1.1 = 211.2 sq ft
- Sheets: 211.2 ÷ 32 = 6.6 → 7 sheets
Buy 7 sheets of 4 × 8 tongue-and-groove subfloor.
How much extra to allow
Sheet goods waste comes from the last sheet in each row and from angled cuts. Simple rectangles waste little; roofs with hips and valleys waste a lot.
| Situation | Allow |
|---|---|
| Rectangular subfloor or wall | 5–10% |
| Walls with many openings | 10% |
| Hip roofs, valleys, dormers | 15% |
Reading your result
The headline is the sheet count to buy. The area with waste above it shows how much coverage you're paying for.
Run sheets with the long edge across the joists or rafters and stagger the end joints. Leave about ⅛ in between sheets for expansion.
On roofs, panel edge clips (H-clips) between rafters support unblocked edges where the span requires them — commonly with 24 in rafter spacing.
Assumptions
- Rectangular surfaces. For an L-shaped floor or a roof with several planes, add the areas first.
- Gable ends, rim joists and roof overhang soffits are not included unless you add them to the area.
- Panel thickness and span rating aren't chosen for you — they depend on joist or rafter spacing and the load.
Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.
When to call a professional
- Structural sheathing — shear walls, roof decks and subfloors — has nailing schedules and panel ratings set by code. Check with your local building department.
- Replacing rotted roof or floor sheathing often uncovers framing damage that needs a contractor.
Frequently asked questions
How many sheets of plywood do I need for a 12 × 12 floor?
144 sq ft × 1.1 = 158.4 ÷ 32 = 4.95, so 5 sheets of 4 × 8.
Is OSB or plywood better for subfloor?
Both are rated for subfloors. OSB is cheaper and more uniform; plywood recovers better from getting wet during construction. Use tongue-and-groove panels rated for your joist spacing either way.
Do I need H-clips on roof sheathing?
They support panel edges between rafters where the span is near the panel's limit, typically at 24 in spacing with thinner panels. The panel stamp and local code decide.
Should I subtract windows and doors from wall sheathing?
Usually not. Most framers sheathe over openings and cut them out, and the offcuts become fillers. Subtract only large openings like garage doors.